- EPSON 4490 SCANNER STUCK RED LIGHT HOW TO
- EPSON 4490 SCANNER STUCK RED LIGHT MANUAL
- EPSON 4490 SCANNER STUCK RED LIGHT UPGRADE
However, there's hope.Īdobe Lightroom (and Apple Aperture) provide a major breakthrough in this regard. Consistency from one scan to the next is always a bugaboo, even with well exposed film, and is much easier to achieve with direct digital capture. Color balance is another matter, along with overall exposure.
EPSON 4490 SCANNER STUCK RED LIGHT MANUAL
Focus and resolution in scanning are no-brainer issues if you hold the film flat and read the user manual regarding the settings. I'm not sure that really makes film better. I sell bicycle components and lead cycle tours for a living.These discussions always seem to center around resolution. Other ways to think us are simply to link to this page, which will help others to find this information should they be looking for it, or to link to our webshop. If I helped you repair your printer and you would like to make a donation of €5 then you can do so by clicking on the button below: Several people have asked me if they can make a donation as a way of saying thank-you for help with repairs. If I do have any problems I shall document them here, including a fix if I have one. Thus far no other problems have arisen with my Samsung printer. You will then be able to print with the not yet empty cartridge for as many pages as the counter would still have allowed for the older emptier cartridge.
Always remove the boards from cartridges which have given print problems before they have stopped working with a red flashing light so that you can use these in cartridges which stop with the red flashing light before they are actually out of toner. If you remove the single screw which holds the printed circuit board in place then you can swap the counter printed circuit board with that from another cartridge. The counter for prints is on a small printed circuit board on the side of the toner cartridge. This is why the red toner light can begin to flash before you've noticed any problem with print quality. Like many modern printers, the ML1640 counts how many "prints" are still in the toner cartridge without reference to actual toner content of the cartridge. Do not bend the switch so far that it is always on - it must switch off when the top is opened. It removes a high voltage supply to the heater when the top is opened. Note that this is a safety critical switch.
However, obviously I don't want to have to lean on the printer each time I want to use it.Ī permanent fix is easy to do - just bend the metal part of the microswitch a little so that the switch is closed when the door is closed. The result of this was that a switch on the power supply board which disconnects the high voltage the heater when the door open, was never closing so the printer simply didn't work at all.Ī little pressure on the top of the printer in the right place would make the red light go out and allow printing. I decided to investigate and found that the cause was simply that the top opening door had deformed with heat. The printer appeared to have turned itself into a paperweight. It was stuck with the red light on and nothing happened when we opened up the front door, the top door inserted or removed paper. Red light stuck onĪfter a couple of years of reliable usage, on one day in August 2012, the printer simply stopped working at the end of a print job. This website provides information but I am not responsible for your actions. Never remove the cover when the printer is plugged in as the power supply board is live and note that capacitors on the board can store very high voltages even when the printer is switched off and disconnected from the mains supply.ĭo not do this work yourself unless you are confident of your ability to protect yourself from shock.
EPSON 4490 SCANNER STUCK RED LIGHT HOW TO
Note that you should never remove the cover unless you know how to protect yourself from shocks. Removing the back cover of the printer reveals the yellow switched mode power supply board on the left and the green processor board on the right.
EPSON 4490 SCANNER STUCK RED LIGHT UPGRADE
Luckily, because we use Linux we never had the opportunity to let the printer upgrade its firmware which have resulted in refills no longer working - so for us they do. Samsung used some horrible techniques to stop you from refilling toner cartridges or using third party cartridges. Sadly, like many products, this one is flawed. So far as print quality and speed for the price are concerned, I think the printer is very good. The Samsung ML-1640 was very low cost, and seemed ideal a couple of years back when we bought it. For our business we need to print quite a lot of black text on a white background, and this is why after owning inkjet printers in the past, I bought a laser printer.